Ac clutch not engaging. How To Manually Engage AC Compressor Clutch: The Easiest Methods 2019-12-01

AC Compressor Clutch Diagnosis & Repair

Ac clutch not engaging

When power energizes the clutch coil, the magnetic field pulls the clutch in towards the pulley. I've attached below a picture of the pressure sensor and its location. Removing the bearing from the clutch rotor. Mineral oil is not compatible with R134. I guess I'll just have to drive with the windows down until I get a new car! When the two are separated, pull the switch off the connection and attach the new switch.

Next

A/C compressor clutch does not engage, cooling fan does n...

Ac clutch not engaging

A loose mounting can cause knocking noises from the compressor area that may be mistaken for internal compressor noise. It could also raise idle speed through control of an idle speed control device. In some vehicles the compressor clutch relay is turned on and off by the low pressure switch and the evaporator temperature sensor. All opinions are my own. Use a socket or wrench to tilt the automatic tensioner away from the belt, and then remove the belt from the pulleys.

Next

What Should You Do When AC Compressor Clutch Not Engaging?

Ac clutch not engaging

. I had tried 3 jy pressure switches before I bought the new one just to be cheap I suppose. It will supply the battery voltage to the compressor clutch, allowing it to engage manually. Changing the compressor clutch could be the only solution in this case. Because the switch is a connection between the canister and the condenser, the refrigerant must be drained from the canister. .

Next

A/C Clutch not engaging

Ac clutch not engaging

I've got two cans in it and it is engaging and blowing a little bit cold. Remove the Woodruff key from the hub and place it aside for future use. . . If the switch had contimuity static, and the clutch does not engage, then test the coil in the clutch for continuity. This switch is located on the metal canister next to the compressor. The cooling fans and condenser fans either are not coming on from a loss of power or the motors are burned up.

Next

AC Compressor Clutch Not Engaging: AC Clutch Does Not Engage. I Am...

Ac clutch not engaging

Well I broke down and took it in to a shop. . If it warms up I might add one more can to finish a try and maybe leave fresh residue from a leak for the shop to find with leak detector. The air is blowing cold not super cold, though. If there is power to the motor, then the condenser fan motor is burned up and will need to be replaced. I had done this before and I did not have problems. How to test the compressor clutch relay Remove the relay from the socket.

Next

What to do When AC Compressor Clutch Is Not Engaging

Ac clutch not engaging

That means the clutch has properly engaged with the pulley. The compressor clutch will engage for like ten seconds only sometimes. I am trying a little bit of everything that will limit the dollars going out. The clutch isn't engaging for a reason, there isn't enough refrigerant in the system. . Would that effect the clutch not to engage. To help you to solve this problem, we are going to give some simple steps in this article.

Next

FIXED! Car A/C Compressor Clutch Won't Engage

Ac clutch not engaging

I just remembered that I had it in to a shop last summer and all it needed was a charge. Check for hard objects such as small stones or sand that may become imbedded in the bottom of the pulley grooves. Now there is a port with a switch or sensor~ 4-wire connector just behind the compressor up at deck level in front of the cooling fan on the passenger side. Consult a shop manual to determine which system your vehicle uses. Its not always this easy and there is more to it than just adding refrigerant but at 200K miles and 13-14 yrs old truck. Next, remove the clutch coil by installing the appropriate puller on the front head of the compressor. With the can attached, pull the trigger and shake the can and it should build enough pressure to trigger the switch.

Next

What to Do If an A/C Compressor Clutch Does Not Disengage

Ac clutch not engaging

This would not only cause a refrigerant leak, but the oil could cause the compressor clutch to slip. If the clutch engages, then check the power supply to the clutch, including the system protection devices and electronic compressor controls. If everything is fine with the fuse, then you have to examine the clutch relay. R-134a high pressure switch operating pressures Prevents compressor clutch operation at pressures at or above 300—psi. No worry about air or losing charge. Remove the compressor mounting bolts and lift the compressor from the engine compartment.

Next

Compressor clutch not engaging — Ricks Free Auto Repair Advice Ricks Free Auto Repair Advice

Ac clutch not engaging

I am concerned that my problem could be with a busted wire. Nevertheless, it is you who take the responsibility for the safety of your vehicle. Start the car and let it run to ensure the compressor clutch disengages. Unlike the cheaper Haynes and Chilton manuals that cover multiple year models, leaving the exact information you need to fix your car, these professional manuals cover your exact year, make, model. Move on to the clutch relay if the fuse turns out fine. I had tried 3 jy pressure switches before I bought the new one just to be cheap I suppose.

Next

What to do When AC Compressor Clutch Is Not Engaging

Ac clutch not engaging

I also tried again unsuccessfully to load the can of Freon, oil, and dye into the system as I did this again about 30 seconds. Now, install the compressor clutch rotor and bearing assembly on the front head. This serves two purposes; it protects the compressor from damage, and prevents venting of refrigerant through the pressure relief device if equipped. . . Other is high pressure and lmore safety switch, should not need to switch.

Next